Double-pole AC version
Conventional thermal current up to 500 A
Rated insulation voltage up to 1,000 V
Auxiliary Switch: 1x S826, 2x cam switching element S007
C158 and C159 – Universally configurable AC and DC contactors up to 500 A
The Schaltbau C158 and C159 contactors are universally configurable single-pole and double-pole cam contactors for AC and DC, with a rated insulation voltage of up to 1000 volts and 500 A continuous current.
C159
Features
Robust design, simple maintenance
The cam contactors C158 and C159 are designed for switching loads frequently. The switching elements can be replaced individually.
DC version with blowout magnets and arcing chambers
During switch off, an electric arc is ignited between the opening contacts. The current flows on through the ionised air. Permanent magnets drive the ionised air out of the contact zone into the arcing chamber. Here, the electric arc is extended and cooled until it goes out.
For DC voltages of up to 300 V, the S310 C cam switching element should be used: with permanent-magnetic blowout and optional electric arc chamber.
Unidirectional DC applications of up to 300 V DC
Single-pole and double-pole cam contactors C158 and C159 can be used in all DC applications up to 300 VDC in which the load does not have to be switched off in both directions:
- Railway technology
- DC drives of machinery
Economy resistor or optional electronic economy circuit
In order to protect the coil of the contactor from excessive heating, a resistor is connected in series with the coil after switch-on.
Optionally, an electronic economy circuit can be chosen. This supplies the required pick-up current for the activation. The current is then regulated down by the electronic economy circuit to the a significantly lower holding current. As a result, the coil becomes less hot and the control power is reduced considerably. The module is attached directly under the contactor.
Up to 4 auxiliary contacts in auxiliary switch blocks
The switch state of the main contacts can be reported to higher-level control systems and devices through auxiliary contacts.
Break contacts, make contacts or combinations of these are available with the cam-operated switching elements of the S007 series. For safety-related tasks, S800 or S826-series snap-action switches can be chosen: Changeover contacts with double-break contact and mechanical positive opening operation .
The auxiliary switch blocks are installed ex-factory. Quantity and contact type are to be specified during the order.
Besondere Merkmale
Robust design, simple maintenance
The cam contactors C158 and C159 are designed for switching loads frequently. The switching elements can be replaced individually.
DC version with blowout magnets and arcing chambers
During switch off, an electric arc is ignited between the opening contacts. The current flows on through the ionised air. Permanent magnets drive the ionised air out of the contact zone into the arcing chamber. Here, the electric arc is extended and cooled until it goes out.
For DC voltages of up to 300 V, the S310 C cam switching element should be used: with permanent-magnetic blowout and optional electric arc chamber.
Unidirectional DC applications of up to 300 V DC
Single-pole and double-pole cam contactors C158 and C159 can be used in all DC applications up to 300 VDC in which the load does not have to be switched off in both directions:
- Railway technology
- DC drives of machinery
Economy resistor or optional electronic economy circuit
In order to protect the coil of the contactor from excessive heating, a resistor is connected in series with the coil after switch-on.
Optionally, an electronic economy circuit can be chosen. This supplies the required pick-up current for the activation. The current is then regulated down by the electronic economy circuit to the a significantly lower holding current. As a result, the coil becomes less hot and the control power is reduced considerably. The module is attached directly under the contactor.
Up to 4 auxiliary contacts in auxiliary switch blocks
The switch state of the main contacts can be reported to higher-level control systems and devices through auxiliary contacts.
Break contacts, make contacts or combinations of these are available with the cam-operated switching elements of the S007 series. For safety-related tasks, S800 or S826-series snap-action switches can be chosen: Changeover contacts with double-break contact and mechanical positive opening operation .
The auxiliary switch blocks are installed ex-factory. Quantity and contact type are to be specified during the order.
Specifications
C158-C159
| Type of voltage | DC, AC |
| Main contacts, configuration | 1 x /2 x NO or NC |
| Nominal voltage Un | 300 V DC |
| Rated insulation voltage Ui | 630 V |
| Conv. thermal current Ith | 500 A |
| Making capacity, resistive T = 0 ms | 2,500 A |
| Contact material main contacts | AgSnO2 |
| Aux. contact | 3 cam switch elements or snap-action switches max. |
| Coil voltage Us | 24, 48, 60, 72, 96, 110, 120, 220 V DC |
| Coil tolerance | -30% … +25% |
| Coil power consumption | Pull-in: approx. 200 W / hold: 38 W |
| IP rating (IEC 60529) | IP00 |
| Mechanical endurance | 2 million operating cycles |
| Temperature range | -25 °C … +70 °C |
| Storage temperature | -40 °C … +80 °C |
| Weight | 5,000 |
/en/products/contactors/thank-you/C158, C159 – Universally configurable AC and DC contactorsContactors